|
About the Sovol SV07 Plus category
|
|
0
|
40
|
March 2, 2025
|
|
First layer problem
|
|
13
|
38
|
December 23, 2025
|
|
X axis isn't centered (off to the right about 10mm)
|
|
13
|
81
|
December 14, 2025
|
|
Cables too short?
|
|
11
|
56
|
December 12, 2025
|
|
Can the SV07+ accept a smart filament sensor?
|
|
1
|
29
|
December 7, 2025
|
|
Best settings for prints
|
|
10
|
127
|
November 13, 2025
|
|
Prints are suddenly like rice paper
|
|
9
|
127
|
November 11, 2025
|
|
Reverse bowden on SV07Plus
|
|
2
|
252
|
November 9, 2025
|
|
TPU print settings
|
|
1
|
76
|
November 2, 2025
|
|
Z-offset smooth vs textured plate
|
|
2
|
62
|
October 26, 2025
|
|
Hotend spare parts or replacement for SV07plus
|
|
6
|
182
|
October 25, 2025
|
|
Printing a circular void
|
|
2
|
28
|
October 20, 2025
|
|
I will never buy another Sovol product-Here's why
|
|
0
|
69
|
October 3, 2025
|
|
SV07 Plus full extruder replacement?
|
|
8
|
215
|
September 25, 2025
|
|
Adhesion & Warping Prints
|
|
13
|
112
|
September 19, 2025
|
|
Sovol sv07 plus+ideamaker profile
|
|
3
|
49
|
September 8, 2025
|
|
SV07 plus Error: heater extruder not heating at expected rate 2
|
|
3
|
99
|
September 8, 2025
|
|
[PROJECT RELEASE] OMEGA_PLR – Reliable Power Loss Recovery for Sovol SV07 Plus (Klipper)
|
|
0
|
106
|
September 6, 2025
|
|
Christian Vicks OrcaSlicer Presets for SOVOL SV07
|
|
10
|
300
|
September 6, 2025
|
|
“Retries Aborting: Probe points range is increasing”
|
|
6
|
131
|
September 4, 2025
|
|
Adding SV07 Plus To Orca Slicer
|
|
4
|
217
|
September 2, 2025
|
|
SOVOL SV07 Plus, OrcaSlicer Networking
|
|
6
|
88
|
August 30, 2025
|
|
Best Filaments SV07 Plus
|
|
5
|
61
|
August 30, 2025
|
|
SV07+ z offset woes
|
|
2
|
51
|
August 21, 2025
|
|
"Reset" printer?
|
|
2
|
43
|
August 16, 2025
|
|
Slow print speeds on Sovol SV07+
|
|
1
|
90
|
August 6, 2025
|
|
One of my two SV07 plus’s are layer shifting
|
|
10
|
199
|
August 4, 2025
|
|
New structural supports at 400 speed a success
|
|
0
|
28
|
July 15, 2025
|
|
Support print does not stick on the bed
|
|
4
|
64
|
June 25, 2025
|
|
Stepper Motor Shorted
|
|
4
|
46
|
June 17, 2025
|