Hi Everyone; Does anybody can tell me how to fix the “exceeds maximum extrusion (0.577mm^2 vs 0.160mm^2)” for the SV06 ACE. I am using the latest version of Orca Slicer. Thank you!!!

Seem to work by replacing 0.24 with 0.06 and 0.16 with 0.04 I am using 0.24*(0.2^2)/(0.4^2)=0.06 and 0.16*(0.2^2)/(0.4^2)=0.04

Read this: [image] Nozzle size change to 0.2 Sovol SV08 Hi, I changed my nozzle size from 0.4 to 0.2. In the printer.cfg under the item “extruder” I also adjusted the nozzle size. Unfortunately I always get a certain error when printing and also z offset calibration. I a…

Hi Lion; Thank you for the reply. I had a look at the machine start G-Code, which I can see in Orca Slicer for the printer profile but I could not find the same codes as he is removing. The Machine Start G-Codes that I have are: M140 S[bed_temperature_initial_layer_single] ;set bed temp M190 S[b…

The is ACE different than the SV08, they are both Klipper but the Start & Ending codes will be different. Also, The ACE only came with a 0.4 Nozzle Profile, unless you created your own 0.2 Nozzle Profile.

Newer versions of Orca come with profiles for 0.2, 0.6, 0.8 on the ACE. I had to click the controls button at the top right of the printer section to select the new profiles so they’d show up in my dropdown.

[image] Lion: Also, The ACE only came with a 0.4 Nozzle Profile, unless you created your own 0.2 Nozzle Profile. [image] GitHub - Sovol3d/Sovol-OrcaSlicer Contribute to Sovol3d/Sovol-OrcaSlicer development by creating an account on GitHub.

I use the latest version of Orca and it did came with the 0.2mm Nozzle Profile. Still the error shows up. I think is related to the purge line that the machine does before starting printing. I am not sure what part of the g-code to modify. Also, in the version of Klipper the machine has, it does no…

These profile still giving me the error message.

taken some screenshots; not sure how to fix this… This is what the extruder is calculating that it should use… [image] After doing mesh levelling, still giving me the same error [image]

This is the extruder printer settings [image] [image]

Fixed, sort off… See Machine G-Code below (following the instructions on the video posted earlier)… Would be good if the start up G-Codes are modified by Sovol rather than reverse engineering the issue… M140 S[bed_temperature_initial_layer_single] ;set bed temp M190 S[bed_temperature_initial_laye…

0.2mm Nozzle - Fixing the "exceeds maximum extrusion (0.577mm^2 vs 0.160mm^2)" error

Sovol SV06 ACE

Lion March 27, 2025, 1:25am 2

Read this:

Topic		Replies	Views
Nozzle size change to 0.2 Sovol SV08	2	1043	March 8, 2025
[SovolSV08] Can't perform Z-Offset calibration in machine after installing 0.200mm nozzle Sovol SV08 advice , leveling	8	113	February 15, 2026
SOVOL dishonest marketing Sovol SV06 Plus ACE	10	422	May 14, 2025
About the Klipperized SV07 category Sovol Klipperized SV07	5	1103	August 4, 2024
What to do after changing the nozzle to 0,2mm Sovol SV06 ACE	6	1052	April 18, 2025

0.2mm Nozzle - Fixing the "exceeds maximum extrusion (0.577mm^2 vs 0.160mm^2)" error

Related topics