Will the official firmware ever support BTT Eddy Probe? I really don’t want to switch to mainline klipper because it’s extremely difficult.

Same here. One comma in code Brick the printer IMHO

[image] Tried putting my sv08 on mainline klipper and now I'm stuck on booting screen Sovol SV08 Tried putting my sv08 on mainline klipper and now I can’t get it to go past the boot screen I’ve tried booting from emmc and sd multiple times and different ones and nothing I’ve tried different images of the cb1 and nothing any help would I’m d be greatly appreciated I can’t portal in I can’t ssh in nothing and it’s super frustrating

On the Sovol Zero launch live stream last week, a few people were asking questions about the SV08 and Sovol indicated that they are working on an Eddy upgrade for the SV08. Their primary focus is the release of the Zero, and a 500 mm coreXY machine they developed in tandem with the Zero, but they promised a user installable Eddy upgrade, presumably with minimal wiring and a firmware upgrade, so it sounds like the Sovol SV08 flavor of Klipper is getting support for Eddy. I was planning to put mainline Klipper on my SV08 specifically to get Eddy probe support, but I also want to keep it running the SV08 version of Klipper to keep it stock in case Sovol pushes future updates. I think I’ll wait for the Sovol Eddy sensor upgrade. The SV08 needs a bed that doesn’t warp 1 mm or more as my SV08 does, but it also needs an accurate temperature compensated bed mesh probe. Those really are my only two issues with the SV08. The other issues were resolved with easy and relatively inexpensive upgrades.

Just go mainline. You might learn a valuable new skill along the way.

It is something I have looked at, but it sounds to complicated!

[image] Liberty4Ever: , I wish/hope they allowed for an ecodered type to be fitted for both detecting Filament Run Out and also Filament Tangled’s, i.e. the encoder wheel stops rotating. I know the SV08 has a option to fit their anti-tangle unit but for me this never worked very well for me, false triggers and other issues..

[image] Liberty4Ever: V08 and Sovol indicated that they are working on an Eddy upgrade for the SV08. Their primary focus is the release of the Zero, and a 500 mm coreXY machine they developed in tandem with the Zero, but they promised a user installable Eddy upgrade, presumably with minimal wiring and a firmware upgrade, so it sounds like the Sovol SV08 flavor of Klipper is getting support for Eddy. I was planning to put mainline Klipper on my SV08 specifically to get Eddy probe support, but I also want to keep it running the SV08 version of Klipper to keep it stock in case Sovol pushes future updates. I think I’ll wait for the Sovol Eddy sensor upgrade. The SV08 needs a bed that doesn’t warp 1 mm or more as my SV08 does, but it also needs an accurate temperature compensated bed mesh probe. Those really are my only two issues with the SV08. The other issues were resolved with easy and relatively inexpensive upgrades. December 2024… two years later, amost ???

This is good to know! I just got a used one and the bed is really warped. I have been heating the bed and the hot end up for a while before I do ABL so I think the induction probe is working correctly even though it’s not temperature compensated?

I wrote nine lines of G code that I appended to the top of the SV08 start G code in OrcaSlicer to preheat the bed and inductive prox sensor for four minutes before each print. It helps but it’s not close to solving the problem of a warped bed and inaccurate bed mesh. SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=65 G28 G90 G1 Z5 F1500 ; Preheat print bed and inductive prox sensor G1 X225 F100 G1 X125 G1 X225 G1 X125 G1 X175 G90 G1 X0 F9000 G1 Y20 G1 Z0.600 F600 G1 Y0 F9000 START_PRINT G90 G1 X0 F9000 G1 Y20 G1 Z0.600 F600 G1 Y0 F9000 M400 G91 M83 M140 S[bed_temperature_initial_layer_single] ;set bed temp M104 S[nozzle_temperature_initial_layer] ;set extruder temp M190 S[bed_temperature_initial_layer_single] ;wait for bed temp M109 S[nozzle_temperature_initial_layer];wait for extruder temp G1 E25 F300 G4 P1000 G1 E-0.200 Z5 F600 G1 X88.000 F9000 G1 Z-5.000 F600 G1 X87.000 E20.88 F1800 G1 X87.000 E13.92 F1800 G1 Y1 E0.16 F1800 G1 X-87.000 E13.92 F1800 G1 X-87.000 E20.88 F1800 G1 Y1 E0.24 F1800 G1 X87.000 E20.88 F1800 G1 X87.000 E13.92 F1800 G1 E-0.200 Z1 F600 M400

Will there be BTT Eddy Probe support in the future?

Sovol SV08

SV08_user December 30, 2024, 10:43am 5

Topic		Replies	Views
Eddy for SV08 without mainline hassle Sovol SV08 challenging	54	3983	July 27, 2025
Eddy and Beacon SV08 Sovol SV08	44	2361	November 1, 2025
Taco bed - BTT Eddy - Belt Tension and all the things Sovol SV08 challenging , leveling	45	3169	July 14, 2025
SV08 updated toolhead and bed...when? Sovol SV08	29	1836	November 5, 2025
SV08 BIGTREETECH EDDY Duo Eddy Coil Sovol SV08	32	6275	November 11, 2025

Will there be BTT Eddy Probe support in the future?

Related topics