# Z aluminium proffiles bumped causing jumps in the prints. SV04

**URL:** <https://forum.sovol3d.com/t/z-aluminium-proffiles-bumped-causing-jumps-in-the-prints-sv04/8585>\
**Category:** Sovol SV04 IDEX\
**Created:** [August 23, 2025, 9:14pm UTC](https://forum.sovol3d.com/t/z-aluminium-proffiles-bumped-causing-jumps-in-the-prints-sv04/8585 "2025-08-23T21:14:40Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![genaro](https://avatars.discourse-cdn.com/v4/letter/g/839c29/32.png) [@genaro](https://forum.sovol3d.com/u/genaro)\
**Post date:** [August 23, 2025, 9:14pm UTC](https://forum.sovol3d.com/t/z-aluminium-proffiles-bumped-causing-jumps-in-the-prints-sv04/8585/1 "2025-08-23T21:14:40Z")

</div>

I recently bought a returned Sovol sv04, I managed to start working quite well with 1 and 2 heads but one thing annoyed me that in all the prints I got the same deformation on the print at the same height.

I discovered what caused the continuous deformation on my prints, after sliding my finger along the inner sides of the gantry , there were some deformations on the aluminum profile on the inner side.

The deformations are not visible to the eye but I can feel them with the touch

Have you experienced the same problem ?

Did you found a solution or a way to mitigate the issue?

Maybe tightening/loosening the eccentric wheels replacing the eccentric wheels for others with a different shape.

Maybe drilling and adding another eccentric wheel on the inside side of the frame ?

(I can’t afford at the moment to replace it for the linear rails)

Thanks in advance for your tips and advice.

 ![i-have-a-gantry-frame-bumped-causing-jumps-in-the-prints-v0-ic8uxws3onkf1](https://canada1.discourse-cdn.com/flex030/uploads/sovolforum/original/2X/7/7f840bfb97d155600d93e8670ff59c2b56890e3a.webp)

---

<div class="post-metadata">

**Author:** ![genaro](https://avatars.discourse-cdn.com/v4/letter/g/839c29/32.png) [@genaro](https://forum.sovol3d.com/u/genaro)\
**Post date:** [August 23, 2025, 9:15pm UTC](https://forum.sovol3d.com/t/z-aluminium-proffiles-bumped-causing-jumps-in-the-prints-sv04/8585/2 "2025-08-23T21:15:26Z")

</div>

![i-have-a-gantry-frame-bumped-causing-jumps-in-the-prints-v0-838wwxs3onkf1](https://canada1.discourse-cdn.com/flex030/uploads/sovolforum/original/2X/c/c88a7d905f4766e6c29d6c2a07d82069977e3e66.webp)

---

<div class="post-metadata">

**Author:** ![Bjoern](https://avatars.discourse-cdn.com/v4/letter/b/46a35a/32.png) [@Bjoern](https://forum.sovol3d.com/u/Bjoern)\
**Post date:** [August 23, 2025, 10:39pm UTC](https://forum.sovol3d.com/t/z-aluminium-proffiles-bumped-causing-jumps-in-the-prints-sv04/8585/3 "2025-08-23T22:39:57Z")

</div>

Hello genaro & welcome to the forum!  
The problem you described is quite unpleasant – you could try to minimize the unevenness with fine sandpaper (e.g., 400 grit) on a right-angled sanding block in the V-slots that are in contact with the rollers.  
Depending on your machining skills, you could try shortening the profiles. Replacement could also be an option – V-slot aluminum profiles 2040 are not particularly expensive.  
Good luck!  
Björn

---

<div class="post-metadata">

**Author:** ![Lion](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/lion/32/5586_2.png) [@Lion](https://forum.sovol3d.com/u/Lion)\
**Post date:** [August 23, 2025, 11:04pm UTC](https://forum.sovol3d.com/t/z-aluminium-proffiles-bumped-causing-jumps-in-the-prints-sv04/8585/4 "2025-08-23T23:04:55Z")

</div>

> [@Bjoern](#):
>
> Replacement could also be an option – V-slot aluminum profiles 2040 are not particularly expensive

I was just going to post this.  
If the frame is dented, replacement might be the only option.

---

<div class="post-metadata">

**Author:** ![genaro](https://avatars.discourse-cdn.com/v4/letter/g/839c29/32.png) [@genaro](https://forum.sovol3d.com/u/genaro)\
**Post date:** [August 24, 2025, 12:49pm UTC](https://forum.sovol3d.com/t/z-aluminium-proffiles-bumped-causing-jumps-in-the-prints-sv04/8585/5 "2025-08-24T12:49:09Z")

</div>

> Thanks for your answers, I am thinking in to use a t slot nut to push the aluminium outwards to reduce the efect on the prints. I wil try this afternoon.

I will try to get parts of 2th hand, one solution is to add linear rails but it’s to early for my to do that conversion.
