# Third party nozzle for SV06 ACE
**URL:** https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417
**Category:** Sovol SV06 ACE
**Created:** [December 31, 2024, 6:48pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417 "2024-12-31T18:48:43Z")
**Posts on this page:** 13
**Page:** 2
### Author:  [@Ouzify](https://forum.sovol3d.com/u/Ouzify)
#### Post date: [January 25, 2025, 4:48pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/21 "2025-01-25T16:48:24Z")
Can confirm the CHT and E3D style nozzles fit with 0 issues
Been printing pretty much daily, testing flows, getting everything dialled in, 0 leaks so far, 0 issues with clogs, it’s been flawless.
Correct that the nozzle does sit a little bit higher up, due to it being shorter, but there is more than enough clearance between the shrouds and the bed.
If anyone is looking for nozzles for these; E3D fit absolutely fine.
---
### Author:  [@minaskar](https://forum.sovol3d.com/u/minaskar)
#### Post date: [January 25, 2025, 5:03pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/22 "2025-01-25T17:03:08Z")
Thanks! That’s what I wanted to hear.
BTW, what kind of max flow rates were you able to achieve with the CHT one?
---
### Author:  [@Ouzify](https://forum.sovol3d.com/u/Ouzify)
#### Post date: [January 26, 2025, 10:58am UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/23 "2025-01-26T10:58:07Z")
Depends on filament
But elegoo rapid pla+ 210 peaked at 41mm3/s
I print it comfortably at 190, 27.5mm3/s
Gives very good overhangs with the stock cooling profile
---
### Author:  [@Oliver](https://forum.sovol3d.com/u/Oliver)
#### Post date: [January 28, 2025, 4:10pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/24 "2025-01-28T16:10:07Z")
Half a mm shorter than the nozzle from Sovol, but available in various diameters from Fysetc as a nozzle for the Creality K1. I installed a nozzle made of hardened steel with a diameter of 0.5 mm. I can’t find any problems.
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [January 28, 2025, 5:11pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/25 "2025-01-28T17:11:29Z")
I ordered 2x .4 nozzles to try them out. They also fit the SV06 Plus…which I also own. 😁
---
### Author:  [@minaskar](https://forum.sovol3d.com/u/minaskar)
#### Post date: [January 28, 2025, 7:03pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/26 "2025-01-28T19:03:45Z")
I thought people had leaking issues with the K1 nozzles on SV08. Did you notice anything?
---
### Author:  [@minaskar](https://forum.sovol3d.com/u/minaskar)
#### Post date: [January 28, 2025, 9:45pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/27 "2025-01-28T21:45:23Z")
[Here’s the reddit post](https://www.reddit.com/r/Sovol/comments/1f1tz9n/sv08_hardened_nozzle_vs_generic_k1_nozzle/) describing the attempt to use K1 nozzles on the SV08. They say it worked fine for a few hours and then you’ll have molten filament coming out of the top.
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [January 28, 2025, 10:34pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/28 "2025-01-28T22:34:17Z")
I won’t test it for awhile, but if I have an issue…I’ll put it in the Plus.
---
### Author:  [@Oliver](https://forum.sovol3d.com/u/Oliver)
#### Post date: [January 29, 2025, 2:32pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/29 "2025-01-29T14:32:56Z")
As I said, the nozzle is 0.5mm shorter than the Sovol nozzle. This makes the nozzle 2mm longer than the Volcano nozzle. I can’t rule out problems! There are also minimal differences in the nozzles depending on the manufacturer. So far I haven’t noticed any problems. But I would like the manufacturers not to “invent” their own nozzle. That is very unpleasant.
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [March 5, 2025, 7:15pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/30 "2025-03-05T19:15:36Z")
Nozzles came in today…and yes I measured them, because why not 😄
@Oliver was correct, as they are 0.5 shorter than the stock ACE nozzle.
But like I posted above,if I have any issues I will just use them in the SV06 Plus (23.4).
Humm…The SV06 Plus are longer also 🙃
---
### Author:  [@sdixon99](https://forum.sovol3d.com/u/sdixon99)
#### Post date: [March 5, 2025, 8:54pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/31 "2025-03-05T20:54:39Z")
Please let us know how your testing goes.
---
### Author:  [@SpoolingItUp](https://forum.sovol3d.com/u/SpoolingItUp)
#### Post date: [October 10, 2025, 11:11pm UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/32 "2025-10-10T23:11:27Z")
Old thread, but did you ever test them/confirm if they work or not?
---
### Author:  [@bundemshake](https://forum.sovol3d.com/u/bundemshake)
#### Post date: [October 13, 2025, 11:30am UTC](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417/33 "2025-10-13T11:30:17Z")
Volcano nozzles were confirmed to work
[Previous page](https://forum.sovol3d.com/t/third-party-nozzle-for-sv06-ace/6417.md?page=1)