# SV07 rebooting whenever I try to preheat the heating bed **URL:** \ **Category:** Sovol Klipperized SV07\ **Created:** [January 23, 2025, 3:39am UTC](https://forum.sovol3d.com/t/sv07-rebooting-whenever-i-try-to-preheat-the-heating-bed/6663 "2025-01-23T03:39:35Z")\ **Posts on this page:** 7\ **Page:** 1
**Author:** ![wwaifu](https://avatars.discourse-cdn.com/v4/letter/w/a5b964/32.png) [@wwaifu](https://forum.sovol3d.com/u/wwaifu)\ **Post date:** [January 23, 2025, 3:39am UTC](https://forum.sovol3d.com/t/sv07-rebooting-whenever-i-try-to-preheat-the-heating-bed/6663/1 "2025-01-23T03:39:35Z")
This is my very first 3D printer. I assembled it as per the manual instructions and walked through all the programming. I was finally ready to do a test print, so I preheated the extruder and everything was fine. Then I tried to preheat the heating board and it rebooted. I’ve tried unplugging and restarting and making sure all the wires were properly inserted, but it reboots every time I try to preheat the heating board no matter if it’s 1 degree more or 50 degrees more. I haven’t done anything to this printer other than what the instructions said. I didn’t even install the optional accelerometer because I just wanted this to be as simple as possible. If anyone has any advice, please let me know! As I’m really eager to test this out. Thanks ---
**Author:** ![Samalexander33](https://avatars.discourse-cdn.com/v4/letter/s/71e660/32.png) [@Samalexander33](https://forum.sovol3d.com/u/Samalexander33)\ **Post date:** [February 4, 2025, 2:49am UTC](https://forum.sovol3d.com/t/sv07-rebooting-whenever-i-try-to-preheat-the-heating-bed/6663/2 "2025-02-04T02:49:20Z")
Howdy! I just received my second SV07 and i am having the exact same problem. Every time the bed temp rises is shuts down and auto reboots. Any advice would be appreciated. ---
**Author:** ![mich0111](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/mich0111/32/1176_2.png) [@mich0111](https://forum.sovol3d.com/u/mich0111)\ **Post date:** [February 4, 2025, 9:14am UTC](https://forum.sovol3d.com/t/sv07-rebooting-whenever-i-try-to-preheat-the-heating-bed/6663/3 "2025-02-04T09:14:46Z")
Open a ticket at [info@sovol3d.com](mailto:info@sovol3d.com) with your order number and pics. They will reply within a week. ---
**Author:** ![badunc](https://avatars.discourse-cdn.com/v4/letter/b/838e76/32.png) [@badunc](https://forum.sovol3d.com/u/badunc)\ **Post date:** [February 14, 2025, 3:20pm UTC](https://forum.sovol3d.com/t/sv07-rebooting-whenever-i-try-to-preheat-the-heating-bed/6663/4 "2025-02-14T15:20:29Z")
I have the same issue with a new SV07. I sent an email to Sovol but whoever gets a response or finds the resolution first please post it here! ---
**Author:** ![badunc](https://avatars.discourse-cdn.com/v4/letter/b/838e76/32.png) [@badunc](https://forum.sovol3d.com/u/badunc)\ **Post date:** [February 16, 2025, 9:45pm UTC](https://forum.sovol3d.com/t/sv07-rebooting-whenever-i-try-to-preheat-the-heating-bed/6663/5 "2025-02-16T21:45:46Z")
NVM, I’m an idiot. I forgot to check the voltage switch and it was set to 230 instead of 115. Problem solved! ---
**Author:** ![wwaifu](https://avatars.discourse-cdn.com/v4/letter/w/a5b964/32.png) [@wwaifu](https://forum.sovol3d.com/u/wwaifu)\ **Post date:** [February 17, 2025, 2:24am UTC](https://forum.sovol3d.com/t/sv07-rebooting-whenever-i-try-to-preheat-the-heating-bed/6663/6 "2025-02-17T02:24:56Z")
This was my problem too! Haha. Glad you figured it out ---
**Author:** ![wwaifu](https://avatars.discourse-cdn.com/v4/letter/w/a5b964/32.png) [@wwaifu](https://forum.sovol3d.com/u/wwaifu)\ **Post date:** [February 17, 2025, 2:26am UTC](https://forum.sovol3d.com/t/sv07-rebooting-whenever-i-try-to-preheat-the-heating-bed/6663/7 "2025-02-17T02:26:27Z")
It’s likely the voltage switch. Make sure it’s set up 115v. ALSO, I realized there were two foam blocks wedged under the heat bed that were preventing full range of motion three days too late \>.\> Wish they’d warn us about those.