# SV07 plus Error: heater extruder not heating at expected rate

**URL:** <https://forum.sovol3d.com/t/sv07-plus-error-heater-extruder-not-heating-at-expected-rate/6615>\
**Category:** Sovol SV07 Plus\
**Tags:** advice, heat-fails\
**Created:** [January 19, 2025, 2:16pm UTC](https://forum.sovol3d.com/t/sv07-plus-error-heater-extruder-not-heating-at-expected-rate/6615 "2025-01-19T14:16:06Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![kokohabpipin](https://avatars.discourse-cdn.com/v4/letter/k/ecd19e/32.png) [@kokohabpipin](https://forum.sovol3d.com/u/kokohabpipin)\
**Post date:** [January 19, 2025, 2:16pm UTC](https://forum.sovol3d.com/t/sv07-plus-error-heater-extruder-not-heating-at-expected-rate/6615/1 "2025-01-19T14:16:06Z")

</div>

Hi everyone, today one of the prints I had printed from yesterday was completed, after taking the product off the plate and leveling everything, I uploaded the next file to print, and whilst the bed was heating up, the extruder itself was stuck on one temperature level (29 degrees). Firmware restard wont do it and I checked i think most of the connection and they seem to be fine. It came as a surprise because it printed perfectly the day before and now suddenly not. Anyone have the same issue?

---

<div class="post-metadata">

**Author:** ![mich0111](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/mich0111/32/1176_2.png) [@mich0111](https://forum.sovol3d.com/u/mich0111)\
**Post date:** [January 19, 2025, 3:01pm UTC](https://forum.sovol3d.com/t/sv07-plus-error-heater-extruder-not-heating-at-expected-rate/6615/2 "2025-01-19T15:01:31Z")

</div>

Hello,  
Try restarting your printer after turning it off to see what happens.

---

<div class="post-metadata">

**Author:** ![kokohabpipin](https://avatars.discourse-cdn.com/v4/letter/k/ecd19e/32.png) [@kokohabpipin](https://forum.sovol3d.com/u/kokohabpipin)\
**Post date:** [January 19, 2025, 6:09pm UTC](https://forum.sovol3d.com/t/sv07-plus-error-heater-extruder-not-heating-at-expected-rate/6615/3 "2025-01-19T18:09:02Z")

</div>

So first turn it off normaly, and press the button on the left side which is the red one off and on like that, or just normally close it, and turn it on again?

---

<div class="post-metadata">

**Author:** ![mich0111](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/mich0111/32/1176_2.png) [@mich0111](https://forum.sovol3d.com/u/mich0111)\
**Post date:** [January 19, 2025, 6:12pm UTC](https://forum.sovol3d.com/t/sv07-plus-error-heater-extruder-not-heating-at-expected-rate/6615/4 "2025-01-19T18:12:12Z")

</div>

Turn it off with the red button.  
By the way, it is best to turn off the printer when the nozzle temperature is below 50°C.