# SV04 Bjorn FW runout sensor on single mode

**URL:** <https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090>\
**Category:** Sovol SV04 IDEX\
**Created:** [June 20, 2025, 8:02pm UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090 "2025-06-20T20:02:35Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![metec](https://avatars.discourse-cdn.com/v4/letter/m/9de053/32.png) [@metec](https://forum.sovol3d.com/u/metec)\
**Post date:** [June 20, 2025, 8:02pm UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090/1 "2025-06-20T20:02:35Z")

</div>

Hello guys,  
my problem is that when printing in single mode with e.g. T0 and T1 is not feeded with filament, I always get the runout failure from unused T1 sensor. How to disable?

Many thanks!

---

<div class="post-metadata">

**Author:** ![cardoc](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/cardoc/32/6926_2.png) [@cardoc](https://forum.sovol3d.com/u/cardoc)\
**Post date:** [June 20, 2025, 8:29pm UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090/2 "2025-06-20T20:29:55Z")

</div>

1 Insert a scrap of filament in the unused sensor.  
OR  
2 Unplug the switch (I’m 90% sure “open” is filament present"

---

<div class="post-metadata">

**Author:** ![metec](https://avatars.discourse-cdn.com/v4/letter/m/9de053/32.png) [@metec](https://forum.sovol3d.com/u/metec)\
**Post date:** [June 20, 2025, 8:43pm UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090/3 "2025-06-20T20:43:31Z")

</div>

Thanks for reply. Ok sounds like a “workaround”. No other option? Just found the marlin “T1 M412 S0” but seems not working -.-

---

<div class="post-metadata">

**Author:** ![Bjoern](https://avatars.discourse-cdn.com/v4/letter/b/46a35a/32.png) [@Bjoern](https://forum.sovol3d.com/u/Bjoern)\
**Post date:** [June 20, 2025, 10:11pm UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090/4 "2025-06-20T22:11:00Z")

</div>

Hello metec,  
thanks for pointing out the issue. There is much room for improvement for handling runout sensors in the current firmware: The touch display handler checks both sensors directly, but ignores the current M412 state. The host handler recognizes M412 instructions, but is not able to separate between both sensors.  
Anyhow, your g-code instruction mentioned above needs two single lines: Otherwise the parser will process T1 only & ignore the rest of the line.

/R  
Björn

---

<div class="post-metadata">

**Author:** ![metec](https://avatars.discourse-cdn.com/v4/letter/m/9de053/32.png) [@metec](https://forum.sovol3d.com/u/metec)\
**Post date:** [June 20, 2025, 10:27pm UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090/5 "2025-06-20T22:27:07Z")

</div>

Hello Björn,  
yes you´re right, once it´s able to separate between both extruder it should be:  
T1 ;  
M412 S0  
T0 ;  
M412 S1

Do you habe experience in using klipper with the SV04? think this is just one step away if already a octopi is in use.

Greetings

---

<div class="post-metadata">

**Author:** ![Bjoern](https://avatars.discourse-cdn.com/v4/letter/b/46a35a/32.png) [@Bjoern](https://forum.sovol3d.com/u/Bjoern)\
**Post date:** [June 20, 2025, 11:12pm UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090/6 "2025-06-20T23:12:10Z")

</div>

Hi again,  
I’m printing via SD-card only or use printrun/pronterface for test purposes - no experience concerning Klipper.  
/R  
Björn

---

<div class="post-metadata">

**Author:** ![metec](https://avatars.discourse-cdn.com/v4/letter/m/9de053/32.png) [@metec](https://forum.sovol3d.com/u/metec)\
**Post date:** [June 20, 2025, 11:56pm UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090/7 "2025-06-20T23:56:40Z")

</div>

Ok thanks again.  
Just one last thing: Are there any possibilies to change the menu language? Cause some guys here in my workshop don´t even speak rudimental english. 😕

---

<div class="post-metadata">

**Author:** ![Bjoern](https://avatars.discourse-cdn.com/v4/letter/b/46a35a/32.png) [@Bjoern](https://forum.sovol3d.com/u/Bjoern)\
**Post date:** [June 21, 2025, 9:32am UTC](https://forum.sovol3d.com/t/sv04-bjorn-fw-runout-sensor-on-single-mode/8090/8 "2025-06-21T09:32:52Z")

</div>

> [@metec](#):
>
> Are there any possibilies to change the menu language?

Sure, it would need to change the images of the display firmware & compile them using [DWIN’s DGUS tool](https://www.dwin-global.com/tool-page/). All images & project files are available in [my GitHub repository](https://github.com/Bjoern70/SV04-Touchscreen).

/R  
Björn
