# Sovol Zero Magnetic Buildplate Holder

**URL:** <https://forum.sovol3d.com/t/sovol-zero-magnetic-buildplate-holder/7857>\
**Category:** Cool Prints & STL Share\
**Created:** [May 22, 2025, 4:28am UTC](https://forum.sovol3d.com/t/sovol-zero-magnetic-buildplate-holder/7857 "2025-05-22T04:28:58Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Lion](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/lion/32/5586_2.png) [@Lion](https://forum.sovol3d.com/u/Lion)\
**Post date:** [May 22, 2025, 4:28am UTC](https://forum.sovol3d.com/t/sovol-zero-magnetic-buildplate-holder/7857/1 "2025-05-22T04:28:58Z")

</div>

For my forum friends.

[Sovol Zero Magnetic Buildplate Holder](https://www.printables.com/model/1303999-sovol-zero-magnetic-buildplate-holder)

 ![PXL_20250522_035020654](https://canada1.discourse-cdn.com/flex030/uploads/sovolforum/original/2X/d/d262ad167534f313d82d01d10b4fa63a6f3f417d.jpeg)

---

<div class="post-metadata">

**Author:** ![Liberty4Ever](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/liberty4ever/32/3265_2.png) [@Liberty4Ever](https://forum.sovol3d.com/u/Liberty4Ever)\
**Post date:** [May 23, 2025, 9:27am UTC](https://forum.sovol3d.com/t/sovol-zero-magnetic-buildplate-holder/7857/2 "2025-05-23T09:27:09Z")

</div>

Very nice work. Thank you!

I bought an inexpensive PEI build plate on Amazon but it’s only 150x150 mm so it’s a bit small, and it doesn’t have the alignment tab in the back. It works but it doesn’t fit well or easily. I should buy a spare or two from Sovol but I guess I’m waiting for them to be on Amazon to facilitate ordering, and maybe they’ll be a bit less expensive. On the plus side, with the Zero making a bed mesh and probing the Z offset before each print, different build plate thicknesses shouldn’t be a problem.

---

<div class="post-metadata">

**Author:** ![Lion](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/lion/32/5586_2.png) [@Lion](https://forum.sovol3d.com/u/Lion)\
**Post date:** [May 23, 2025, 1:59pm UTC](https://forum.sovol3d.com/t/sovol-zero-magnetic-buildplate-holder/7857/3 "2025-05-23T13:59:42Z")

</div>

> [@Liberty4Ever](#):
>
> I bought an inexpensive PEI build plate on Amazon but it’s only 150x150 mm

The plate is 162 mm²

---

<div class="post-metadata">

**Author:** ![jbob](https://avatars.discourse-cdn.com/v4/letter/j/b487fb/32.png) [@jbob](https://forum.sovol3d.com/u/jbob)\
**Post date:** [May 24, 2025, 11:24am UTC](https://forum.sovol3d.com/t/sovol-zero-magnetic-buildplate-holder/7857/4 "2025-05-24T11:24:20Z")

</div>

Nice touch. How often do you switch out build plates?

---

<div class="post-metadata">

**Author:** ![Lion](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/lion/32/5586_2.png) [@Lion](https://forum.sovol3d.com/u/Lion)\
**Post date:** [May 24, 2025, 11:47am UTC](https://forum.sovol3d.com/t/sovol-zero-magnetic-buildplate-holder/7857/5 "2025-05-24T11:47:21Z")

</div>

Right now I’m mostly using the Blue plate.  
I will normally switch a plate when a model sticks too well & I need to keep printing…  
…or I need to clean the plate.  
The Glacier is good for all filaments.

If I didn’t cut it down I would have bought another Sovol plate, for the same reasons posted above.
