# Sovol SV06 power outage?
**URL:** https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014
**Category:** Sovol SV06 Fully Open Source 3D Printer
**Created:** [November 15, 2025, 12:24pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014 "2025-11-15T12:24:55Z")
**Posts on this page:** 13
**Page:** 1
### Author:  [@edtineo](https://forum.sovol3d.com/u/edtineo)
#### Post date: [November 15, 2025, 12:24pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/1 "2025-11-15T12:24:55Z")
Hello all,
I bought a Sovol SV06 on Facebook market and I cleaned it up. Re greased the rails and rods. Checked all the screws and plugs to make sure all was working properly. I took apart the Hotend and made sure that the nozzle and heat end works. I set the z off-set and leveled the bed. all works fine and looks great. I also re flashed the firmware.
But after I sliced a benchy file and put in the newly formated sd card, I kept getting a Power Outage/ printer haulted/ please reset prompt. I looked online and did all that was recommended like turning it off and hitting resume printing but it happened again. I unplugged it and rechecked all the plugs and wiring. Still keep getting the same prompt.
The nozzle heats up, I pushed filament thru and it feeds thru fine. The bed heats up and reaches temp. so all the heat elements are working. I saw something about adding a Line of Gcode to sliced file, but i dont know how to do that. Any suggestions.
I really like Sovol and Own an SV01 and an SV07 plus but I just really want to get this working. I love tinkering with 3D printers and buying older printers and getting them working again. so can anyone one help?
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [November 15, 2025, 1:01pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/2 "2025-11-15T13:01:15Z")
It looks like it thinks there was a power outage…
Do you get a prompt that says Resume Print & Stop Print..??
If so, click on Stop Print.
---
### Author:  [@edtineo](https://forum.sovol3d.com/u/edtineo)
#### Post date: [November 15, 2025, 1:29pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/3 "2025-11-15T13:29:22Z")
yes, I have done that. But it happens every time I try to print anything. I haven’t printed anything with it yet. It heats up and says its about to start print and then stops and I get the prompt. it wont go past the heating up bed and nozzle then moves to start print and then stops. I shut it off, restart. It asks if I want to continue print. I press yes, same prompt. I say no then try a new print, same prompt. I tried fixing model in Bambu, Orca, Cura, Creality slicer. nothing but Power Outage, Printer haulted, Please reset. Repeat, start print, Power outage, restart, repeat.
---
### Author:  [@edtineo](https://forum.sovol3d.com/u/edtineo)
#### Post date: [November 15, 2025, 1:35pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/4 "2025-11-15T13:35:50Z")
This isn’t my first printer. I have Ender 3 , ender 3 pros, ender 3 s1, ender 3v 3 se, K1max, a1, a1 mini, neptune 3 pro, plus and max. sovol SV0l, SV07 plus. I own may printers. Usaually a firmware update or older version firmware fixes things. I bad plug or thermister, a bad motherboard but all seems fine. Just can’t figure this out.
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [November 15, 2025, 1:55pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/5 "2025-11-15T13:55:40Z")
It might sound obvious, but have you checked the power setting…115v-230v.
Also, can you get to the Main Screen at all..??
If you can, go into Configuration/Advanced Settings/Initialize EEPROM… then Configuration/Restore Defaults.
---
### Author:  [@edtineo](https://forum.sovol3d.com/u/edtineo)
#### Post date: [November 15, 2025, 2:06pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/6 "2025-11-15T14:06:43Z")
yes, ive done all that. nothing.
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [November 15, 2025, 2:25pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/7 "2025-11-15T14:25:17Z")
My only thought is to re-flash Marlin again.
Have you tried starting the printer with the SD Card removed…maybe it’s something in your code. Are you using Cura or Orca Slicer..??
---
### Author:  [@edtineo](https://forum.sovol3d.com/u/edtineo)
#### Post date: [November 15, 2025, 2:29pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/8 "2025-11-15T14:29:24Z")
is that not the updated firmware? if not where do i get that marlin flash? I have used Bambu, Creality, Cura, Orca slicers. ill try the sd card thing now. ill let u know how that works.
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [November 15, 2025, 2:44pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/9 "2025-11-15T14:44:09Z")
Each slicer has it’s own Start Gcode, the SV06 came with Cura…so stay with that for now until it’s fixed.
You can find the firmware here, with & without filament sensor:
> **[Firmware Download](https://www.sovol3d.com/pages/download)**
>
> SOVOL SV01 SV02 SV03 SV04 SV05 SV01PRO SV06 SV06PLUS SV07 SV07PLUS COMGROW LASER Z1 Z1PRO T500 T300 FIRMWARE SLICER CURA SETTING.
---
### Author:  [@edtineo](https://forum.sovol3d.com/u/edtineo)
#### Post date: [November 15, 2025, 2:45pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/10 "2025-11-15T14:45:23Z")
ok but, is that firmware on [sovol.com](http://sovol.com) the firmware for marlin?
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [November 15, 2025, 3:00pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/11 "2025-11-15T15:00:09Z")
The link above is for Marlin, Sovol didn’t start using Klipper until the SV07.
The 1st round of SV06’s came without a filament sensor..mine has a custom install..about 3-6 months later, Sovol added a filament sensor to the SV06. That is why there are 2 different firmware versions.
---
### Author:  [@edtineo](https://forum.sovol3d.com/u/edtineo)
#### Post date: [November 15, 2025, 3:10pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/12 "2025-11-15T15:10:09Z")
thank you so much, I googled marling firmware for the SV06 and downloaded it from github and ,then i was able to disable power outage. guess what. its printing. THANKS SO MUCH! I got it for $40 dollars. what a steal!
---
### Author:  [@Lion](https://forum.sovol3d.com/u/Lion)
#### Post date: [November 15, 2025, 4:20pm UTC](https://forum.sovol3d.com/t/sovol-sv06-power-outage/9014/13 "2025-11-15T16:20:38Z")
It’s a great printer, your should look into the SV06 Plus if you need something bigger 😁