# Sovol 3D SO-2 Homing Failed

**URL:** <https://forum.sovol3d.com/t/sovol-3d-so-2-homing-failed/1610>\
**Category:** Laser Engraving\
**Created:** [February 9, 2023, 4:01pm UTC](https://forum.sovol3d.com/t/sovol-3d-so-2-homing-failed/1610 "2023-02-09T16:01:24Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![jgomez](https://avatars.discourse-cdn.com/v4/letter/j/9fc29f/32.png) [@jgomez](https://forum.sovol3d.com/u/jgomez)\
**Post date:** [February 9, 2023, 4:01pm UTC](https://forum.sovol3d.com/t/sovol-3d-so-2-homing-failed/1610/1 "2023-02-09T16:01:24Z")

</div>

I have been using my SO-2 as a pen plotter. It was working fine until last night when I tried to plot some writting and it got stuck trying to find home. The only thing I remember doing differently than other time was that as soon as I turned it on pressed the home button without letting it “start” properly. Now every time I try to home the pen it gets stuck and gives an error that says homing failed. And when it manages to get home and I try to start to draw the X axis where the pen is placed doesn’t manage to move freely.

Any help or adviced is appreciated I am very happy with my device is helping me do exactly what I need to do however I do not know how to fix this problem. Thank you for any advice or help on the matter.

---

<div class="post-metadata">

**Author:** ![Bjoern](https://avatars.discourse-cdn.com/v4/letter/b/46a35a/32.png) [@Bjoern](https://forum.sovol3d.com/u/Bjoern)\
**Post date:** [February 10, 2023, 6:13am UTC](https://forum.sovol3d.com/t/sovol-3d-so-2-homing-failed/1610/2 "2023-02-10T06:13:00Z")

</div>

Did check the mechanical components of your X-axis:

- the timing belt is intact & has all teeth & the belt tension is sufficient (should be the same tension as on Y-axis belt);
- no difference in resistance when moving the printhead (writehead) along the X-axis by hand (motors have to be powered off);
- all eccentric roller bearings located on the X-axis are fitting without play & same pressure;
- all roller treads are free of dirt;
- the travel paths of the rollers on the v-slot profile are free of dirt on top & bottom side

---

<div class="post-metadata">

**Author:** ![sovol3d](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/sovol3d/32/9_2.png) [@sovol3d](https://forum.sovol3d.com/u/sovol3d)\
**Post date:** [February 11, 2023, 1:52am UTC](https://forum.sovol3d.com/t/sovol-3d-so-2-homing-failed/1610/3 "2023-02-11T01:52:11Z")

</div>

hi @Bjoern Appreciate your detailed analysis. 🤗 @jgomez Besides what Bjoern has suggested, could you pls also try reflashing the firmware via reloading the firmware  
[firmware.bin](https://forum.sovol3d.com/uploads/short-url/zxEJJqvWHo9YJRLH1InHOJVUqm1.bin) (33.0 KB) to the sd card and replugging it into the machine when it’s shut down then waiting for 20 seconds?

If that doesn’t work, pls add a video to show the case, thanks in advance!

---

<div class="post-metadata">

**Author:** ![jgomez](https://avatars.discourse-cdn.com/v4/letter/j/9fc29f/32.png) [@jgomez](https://forum.sovol3d.com/u/jgomez)\
**Post date:** [February 14, 2023, 8:33pm UTC](https://forum.sovol3d.com/t/sovol-3d-so-2-homing-failed/1610/4 "2023-02-14T20:33:20Z")

</div>

Thank you for all your helpful advice. I finally have sometime to check my device. I am trying to reflash the firmware however I cannot find a place where to put the sd card in my device, Sovel 3D SO-2. Do i have to flash it from the PC?  
Thanks.

---

<div class="post-metadata">

**Author:** ![jgomez](https://avatars.discourse-cdn.com/v4/letter/j/9fc29f/32.png) [@jgomez](https://forum.sovol3d.com/u/jgomez)\
**Post date:** [February 14, 2023, 9:08pm UTC](https://forum.sovol3d.com/t/sovol-3d-so-2-homing-failed/1610/5 "2023-02-14T21:08:30Z")

</div>

Here are some videos.

When trying to home it gets stuck half way.

[video1](https://www.youtube.com/shorts/p6SnGrJ5Mn8)

Trying to home again, there is some grinding sounds.

[video2](https://www.youtube.com/shorts/p9JNbyA8G-s)

Thank you in advance.

---

<div class="post-metadata">

**Author:** ![Darek](https://avatars.discourse-cdn.com/v4/letter/d/d78d45/32.png) [@Darek](https://forum.sovol3d.com/u/Darek)\
**Post date:** [March 30, 2023, 3:37pm UTC](https://forum.sovol3d.com/t/sovol-3d-so-2-homing-failed/1610/6 "2023-03-30T15:37:16Z")

</div>

I have the same problem with homing. The head is stuck in some position. Woh to reset to fatory settings or how to load the firmware.
