# Print Breaks MidWay Through on My Sv06

**URL:** <https://forum.sovol3d.com/t/print-breaks-midway-through-on-my-sv06/4512>\
**Category:** Sovol SV06 Fully Open Source 3D Printer\
**Created:** [February 13, 2024, 11:50pm UTC](https://forum.sovol3d.com/t/print-breaks-midway-through-on-my-sv06/4512 "2024-02-13T23:50:48Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Fallen\_Coop](https://avatars.discourse-cdn.com/v4/letter/f/d9b06d/32.png) [@Fallen\_Coop](https://forum.sovol3d.com/u/Fallen_Coop)\
**Post date:** [February 13, 2024, 11:50pm UTC](https://forum.sovol3d.com/t/print-breaks-midway-through-on-my-sv06/4512/1 "2024-02-13T23:50:48Z")

</div>

I am VERY new to 3d printing and during the middle of my prints it just… breaks? I am using beagle print to print from my phone but I am pretty sure that has nothing to do with it. I hear some cracking and then boom the print is in a different place and there is a pile of spaghetti everywhere. have tried putting some hairspray and glue on the bed where the print is but that did not help. I think the extruder is knocking the print over. I am using PLA and running at 100% cooling: 60 bed temp: and 195 end temp. What do I do?

---

<div class="post-metadata">

**Author:** ![Lion](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/lion/32/5586_2.png) [@Lion](https://forum.sovol3d.com/u/Lion)\
**Post date:** [February 13, 2024, 11:57pm UTC](https://forum.sovol3d.com/t/print-breaks-midway-through-on-my-sv06/4512/2 "2024-02-13T23:57:16Z")

</div>

I’m gonna guess & say your using Cubic infill…change your infill to Gyroid.  
Cubic & similar infill patterns will hit the nozzle when it passes over itself.

---

<div class="post-metadata">

**Author:** ![Fallen\_Coop](https://avatars.discourse-cdn.com/v4/letter/f/d9b06d/32.png) [@Fallen\_Coop](https://forum.sovol3d.com/u/Fallen_Coop)\
**Post date:** [February 14, 2024, 12:15am UTC](https://forum.sovol3d.com/t/print-breaks-midway-through-on-my-sv06/4512/3 "2024-02-14T00:15:50Z")

</div>

Ah, I see. I have changed it to gyroid. I was using zig zag but i guess that is similar enough to cubic. I tried again and the print still hit the nozzle. Tell me if you need more info

---

<div class="post-metadata">

**Author:** ![Fallen\_Coop](https://avatars.discourse-cdn.com/v4/letter/f/d9b06d/32.png) [@Fallen\_Coop](https://forum.sovol3d.com/u/Fallen_Coop)\
**Post date:** [February 14, 2024, 12:19am UTC](https://forum.sovol3d.com/t/print-breaks-midway-through-on-my-sv06/4512/4 "2024-02-14T00:19:30Z")

</div>

By the way I have Leveled my bad and my z axis.It is definitely hitting the extruder. I just need a way to keep that from happening