# Oozy END\_PRINT & runout bugs

**URL:** https://forum.sovol3d.com/t/oozy-end-print-runout-bugs/10341
**Category:** Sovol SV08
**Tags:** klipper
**Created:** [August 30, 2026, 10:16pm UTC](https://forum.sovol3d.com/t/oozy-end-print-runout-bugs/10341 "2026-08-30T22:16:05Z")
**Posts on this page:** 4
**Page:** 1

<div class="post-metadata">

### Author: ![rpcyan](https://avatars.discourse-cdn.com/v4/letter/r/34f0e0/32.png) [@rpcyan](https://forum.sovol3d.com/u/rpcyan)
#### Post date: [August 30, 2026, 10:16pm UTC](https://forum.sovol3d.com/t/oozy-end-print-runout-bugs/10341/1 "2026-08-30T22:16:05Z")

</div>

Also evidently impacts the SV08

> [@Oozy END\_PRINT bugfix (& filament runout/resume bugs)](https://forum.sovol3d.com/t/oozy-end-print-bugfix-filament-runout-resume-bugs/10312):
>
> I found a bug in the end\_print macro. It is present in ALL of Zero’s firmwares. EDIT: Bugs also in SV06 ACE, SV08, and SV08 Max Sovol intends to retract 4mm (with a little z hop in the middle) in this code block, which would reduce ooze at the end of the print and crud to deal with at the start of the next: {% if printer['filament\_switch\_sensor filament\_sensor'].enable == True and printer['filament\_switch\_sensor filament\_sensor'].filament\_detected == True %} {% if (printer.extruder.t…

---

<div class="post-metadata">

### Author: ![Alien\_Soldier](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/alien_soldier/32/6296_2.png) [@Alien\_Soldier](https://forum.sovol3d.com/u/Alien_Soldier)
#### Post date: [September 1, 2026, 1:32pm UTC](https://forum.sovol3d.com/t/oozy-end-print-runout-bugs/10341/2 "2026-09-01T13:32:52Z")

</div>

Thanks for the information. However, I didn’t find such a problem on my sv08 printer. In all macros, the values are set to “enable”. I purchased the printer on May 10 of this year. The firmware version is listed as 2.5.0 (2025.11.14).

I was wrong; I’m encountering the same problem mentioned earlier…

---

<div class="post-metadata">

### Author: ![mich0111](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/mich0111/32/1176_2.png) [@mich0111](https://forum.sovol3d.com/u/mich0111)
#### Post date: [September 1, 2026, 2:01pm UTC](https://forum.sovol3d.com/t/oozy-end-print-runout-bugs/10341/3 "2026-09-01T14:01:08Z")

</div>

Shouldn’t it be set to “enabled”?

---

<div class="post-metadata">

### Author: ![Alien\_Soldier](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/alien_soldier/32/6296_2.png) [@Alien\_Soldier](https://forum.sovol3d.com/u/Alien_Soldier)
#### Post date: [September 1, 2026, 3:42pm UTC](https://forum.sovol3d.com/t/oozy-end-print-runout-bugs/10341/4 "2026-09-01T15:42:05Z")

</div>

At that moment, I got confused.