# Klipper-What do you put in printer.cfg file? **URL:** \ **Category:** Sovol SV06 Fully Open Source 3D Printer\ **Tags:** klipper\ **Created:** [September 23, 2024, 2:44am UTC](https://forum.sovol3d.com/t/klipper-what-do-you-put-in-printer-cfg-file/5712 "2024-09-23T02:44:40Z")\ **Posts on this page:** 3\ **Page:** 1
**Author:** ![Chief](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/chief/32/2025_2.png) [@Chief](https://forum.sovol3d.com/u/Chief)\ **Post date:** [September 23, 2024, 2:44am UTC](https://forum.sovol3d.com/t/klipper-what-do-you-put-in-printer-cfg-file/5712/1 "2024-09-23T02:44:40Z")
I am using octoprint with klipper on my sv06 and it is giving me a ton of warnings related to the printer.cfg file and I cant really figure out what exactly I’m supposed to put in the file, I’ve tried different things and they haven’t worked. is there anything I can just copy paste and put in there? ---
**Author:** ![sovol3d](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/sovol3d/32/9_2.png) [@sovol3d](https://forum.sovol3d.com/u/sovol3d)\ **Post date:** [September 25, 2024, 3:09am UTC](https://forum.sovol3d.com/t/klipper-what-do-you-put-in-printer-cfg-file/5712/2 "2024-09-25T03:09:48Z")
Thank you so much for buying from Sovol, and I apologize for all the inconvenience. Did you already send an email to [info@sovol3d.com](mailto:info@sovol3d.com)? If not, please send the above situation with videos and pictures and your order number, and we will check with the engineers asap. ---
**Author:** ![zogthegreat](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/zogthegreat/32/2437_2.png) [@zogthegreat](https://forum.sovol3d.com/u/zogthegreat)\ **Post date:** [December 4, 2024, 1:36pm UTC](https://forum.sovol3d.com/t/klipper-what-do-you-put-in-printer-cfg-file/5712/3 "2024-12-04T13:36:26Z")
Hi @Chief , I just saw your post, I’m hoping that you got things going already. But if you haven’t, here is an example of my printer.cfg for the SV06. Do not to just copy and paste, my setup will be different from yours. But this will give you a general idea of what you need: [mcu] # NOTE Obtain definition by “ls -l /dev/serial/by-path/” or “ls -l /dev/serial/by-id/” serial: /dev/serial/by-id/usb-1a86\_USB\_Serial-if00-port0 restart\_method: command [printer] kinematics: cartesian max\_velocity: 200 max\_accel: 3000 max\_z\_velocity: 15 max\_z\_accel: 45 square\_corner\_velocity: 8.0 ##################################################################### # X/Y/Z Stepper Settings ##################################################################### [stepper\_x] step\_pin: PC2 dir\_pin: !PB9 enable\_pin: !PC3 microsteps: 128 ;microsteps: 16 rotation\_distance: 40 endstop\_pin: tmc2209\_stepper\_x:virtual\_endstop position\_endstop: 0 position\_max: 223 # NOTE You can adjust this if you have more room homing\_speed: 40 homing\_retract\_dist: 0 [tmc2209 stepper\_x] uart\_pin: PC1 run\_current: 0.85 ;1.0 stealthchop\_threshold: 0 interpolate: False sense\_resistor: 0.150 uart\_address: 3 driver\_SGTHRS: 81 diag\_pin: PA5 [stepper\_y] step\_pin: PB8 dir\_pin: !PB7 enable\_pin: !PC3 microsteps: 128 ;microsteps: 16 rotation\_distance: 40 endstop\_pin: tmc2209\_stepper\_y:virtual\_endstop position\_endstop: 0 position\_max: 223 # NOTE You can adjust this if you have more room homing\_speed: 40 homing\_retract\_dist: 0 [tmc2209 stepper\_y] uart\_pin: PC0 run\_current: 0.85 ;1.0 stealthchop\_threshold: 0 interpolate: False sense\_resistor: 0.150 uart\_address: 3 driver\_SGTHRS: 81 diag\_pin: PA6 [stepper\_z] step\_pin: PB6 dir\_pin: PB5 enable\_pin: !PC3 microsteps: 128 ;microsteps: 16 rotation\_distance: 4 endstop\_pin: probe:z\_virtual\_endstop position\_min: -4 position\_max: 258 # NOTE You can adjust this if you have more room homing\_speed: 5 [tmc2209 stepper\_z] uart\_pin: PA15 run\_current: 0.85 ;1.0 stealthchop\_threshold: 0 interpolate: False sense\_resistor: 0.150 uart\_address: 3 diag\_pin: PA7 ##################################################################### # Extruder ##################################################################### [extruder] step\_pin: PB4 dir\_pin: !PB3 enable\_pin: !PC3 microsteps: 16 rotation\_distance: 4.65 # NOTE Calibrate e-steps [Rotation distance - Klipper documentation](https://www.klipper3d.org/Rotation_Distance.html#calibrating-rotation_distance-on-extruders), [https://github.com/bassamanator/everything-sovol-sv06/blob/main/howto.md#calibrate-esteps](https://github.com/bassamanator/everything-sovol-sv06/blob/main/howto.md#calibrate-esteps) nozzle\_diameter: 0.400 filament\_diameter: 1.750 heater\_pin: PA1 sensor\_type: EPCOS 100K B57560G104F sensor\_pin: PC5 #control: pid #pid\_kd: 86.991 #pid\_kp: 21.479 #pid\_ki: 1.326 min\_temp: 0 max\_temp: 300 max\_extrude\_only\_distance: 150.0 max\_extrude\_cross\_section: 5 # NOTE Needed for KAMP purge [tmc2209 extruder] uart\_pin: PC14 run\_current: 0.550 stealthchop\_threshold: 0 interpolate: False sense\_resistor: 0.150 uart\_address: 3 ##################################################################### # Bed Heater ##################################################################### [heater\_bed] heater\_pin: PA2 sensor\_type: EPCOS 100K B57560G104F sensor\_pin: PC4 #control: pid #pid\_kp: 64.440 #pid\_ki: 0.773 #pid\_kd: 1343.571 min\_temp: 0 max\_temp: 110 ##################################################################### # Probe Related ##################################################################### [probe] pin: PB1 x\_offset: 27 y\_offset: -20 #z\_offset: 0 samples: 3 samples\_result: median samples\_tolerance: 0.01 samples\_tolerance\_retries: 5 [safe\_z\_home] home\_xy\_position: 84.50, 135 # NOTE The probe is at the center of the bed. speed: 100.0 z\_hop: 10 z\_hop\_speed: 15 [bed\_mesh] speed: 175 mesh\_min: 27, 6 # probe as close to origin as possible while remaining fully on the bed mesh\_max: 222, 203 # (x.position\_max - 1), (y.position\_max - abs(y\_offset)) ; probe as far as possible from the origin while remaining fully on the bed probe\_count: 5,5 algorithm: bicubic fade\_start: 1 fade\_end: 10 fade\_target: 0 [axis\_twist\_compensation] calibrate\_start\_x: 27 # probe x coor at furthest left ; abs(x\_offset) calibrate\_end\_x: 195 # probe x coor at furthest right ; (x.position\_max - abs(x\_offset) - 1) calibrate\_y: 115 ##################################################################### # Fans ##################################################################### [fan] pin: PA0 ##################################################################### # Misc ##################################################################### [display] lcd\_type: st7920 cs\_pin: PB12 sclk\_pin: PB13 sid\_pin: PB15 encoder\_pins: ^PB14, ^PB10 click\_pin: ^!PB2 [bed\_screws] screw1\_name: front left screw1: 26.5, 31 screw2\_name: front right screw2: 196.75, 31 screw3\_name: back right screw3: 196.75, 201 screw4\_name: back left screw4: 26.5, 201 [screws\_tilt\_adjust] screw1\_name: center screw1: 84.50, 135 screw2\_name: front left screw2: 0, 51 screw3\_name: front right screw3: 169.75, 51 screw4\_name: back right screw4: 169.75, 221 screw5\_name: back left screw5: 0, 221 horizontal\_move\_z: 10 screw\_thread: CCW-M4 [output\_pin beeper] pin: PC6 value: 0 shutdown\_value: 0 pwm: True cycle\_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz) [filament\_switch\_sensor filament\_sensor] switch\_pin: !PA4 # “Pulled-high” pause\_on\_runout: True insert\_gcode: M117 Insert Detected { action\_respond\_info(“Insert Detected”) } runout\_gcode: M117 Runout Detected { action\_respond\_info(“Runout Detected”) } CONDITIONAL\_BEEP i=3 dur=300 freq=400