# Community Guru help needed **URL:** \ **Category:** Sovol SV06 Plus\ **Created:** [June 15, 2023, 11:19pm UTC](https://forum.sovol3d.com/t/community-guru-help-needed/2866 "2023-06-15T23:19:18Z")\ **Posts on this page:** 3\ **Page:** 1
**Author:** ![meicalnissyen](https://avatars.discourse-cdn.com/v4/letter/m/ac91a4/32.png) [@meicalnissyen](https://forum.sovol3d.com/u/meicalnissyen)\ **Post date:** [June 15, 2023, 11:19pm UTC](https://forum.sovol3d.com/t/community-guru-help-needed/2866/1 "2023-06-15T23:19:18Z")
Hey All, for those of you that have this beast sorted to the point you can pull the trigger with confidence on an overnite print and know itll be good, I would very much like to know what your stepper currents, and hybrid threshold values are. TIA ---
**Author:** ![Lion](https://yyz2.discourse-cdn.com/flex030/user_avatar/forum.sovol3d.com/lion/32/5586_2.png) [@Lion](https://forum.sovol3d.com/u/Lion)\ **Post date:** [June 15, 2023, 11:55pm UTC](https://forum.sovol3d.com/t/community-guru-help-needed/2866/2 "2023-06-15T23:55:56Z")
I just posted a little while ago… > [@Print failures and crazy noise / sounds with new SV06 Plus](https://forum.sovol3d.com/t/print-failures-and-crazy-noise-sounds-with-new-sv06-plus/2857/8): > > Have you been playing around with the TMC Driver Settings…?? Advanced Settings/TMC Drivers…match with pics. ---
**Author:** ![meicalnissyen](https://avatars.discourse-cdn.com/v4/letter/m/ac91a4/32.png) [@meicalnissyen](https://forum.sovol3d.com/u/meicalnissyen)\ **Post date:** [June 16, 2023, 3:25pm UTC](https://forum.sovol3d.com/t/community-guru-help-needed/2866/3 "2023-06-16T15:25:37Z")
SENDING:M503 echo:; Linear Units: G21 ; (mm) echo:; Temperature Units: echo: M149 C ; Units in Celsius echo:; Filament settings (Disabled): echo: M200 S0 D1.75 echo:; Steps per unit: echo: M92 X80.00 Y80.00 Z800.00 E684.00 echo:; Max feedrates (units/s): echo: M203 X300.00 Y300.00 Z15.00 E120.00 echo:; Max Acceleration (units/s2): echo: M201 X800.00 Y800.00 Z200.00 E4000.00 echo:; Acceleration (units/s2) (P R T): echo: M204 P800.00 R800.00 T800.00 echo:; Advanced (B\ S\ T\ X\ Y\ Z\ E\): echo: M205 B20000.00 S0.00 T0.00 X5.00 Y5.00 Z0.30 E4.50 echo:; Home offset: echo: M206 X0.00 Y0.00 Z0.00 echo:; Auto Bed Leveling: echo: M420 S1 Z20.00 ; Leveling ON echo: G29 W I0 J0 Z0.71260 echo: G29 W I1 J0 Z0.31385 echo: G29 W I2 J0 Z0.00635 echo: G29 W I3 J0 Z-0.29490 echo: G29 W I4 J0 Z-0.63740 echo: G29 W I0 J1 Z0.79010 echo: G29 W I1 J1 Z0.38260 echo: G29 W I2 J1 Z0.04385 echo: G29 W I3 J1 Z-0.31990 echo: G29 W I4 J1 Z-0.70490 echo: G29 W I0 J2 Z0.80885 echo: G29 W I1 J2 Z0.40510 echo: G29 W I2 J2 Z0.03885 echo: G29 W I3 J2 Z-0.35115 echo: G29 W I4 J2 Z-0.74615 echo: G29 W I0 J3 Z0.77760 echo: G29 W I1 J3 Z0.37260 echo: G29 W I2 J3 Z0.03135 echo: G29 W I3 J3 Z-0.33365 echo: G29 W I4 J3 Z-0.72240 echo: G29 W I0 J4 Z0.71885 echo: G29 W I1 J4 Z0.33760 echo: G29 W I2 J4 Z0.03885 echo: G29 W I3 J4 Z-0.27115 echo: G29 W I4 J4 Z-0.63615 echo:; Material heatup parameters: echo: M145 S0 H195.00 B60.00 F0 echo: M145 S1 H240.00 B80.00 F0 echo:; Hotend PID: echo: M301 P24.03 I2.84 D50.79 echo:; Bed PID: echo:echo: M304 P375.00 I75.00 D1350.00 echo:; User thermistors: echo: M305 P0 R4700.0 T94162.0 B4160.0 C0.000000000 ; HOTEND 0 echo:; LCD Brightness: echo: M256 B250 echo:; Power-loss recovery: echo: M413 S1 ; ON echo:; Z-Probe Offset: echo: M851 X25.00 Y-25.00 Z-1.57 ; (mm) echo:; Stepper driver current: echo: M906 X820 Y880 Z800 echo: M906 T0 E550 echo:; Hybrid Threshold: echo: M913 X253 Y253 Z61 echo: M913 T0 E82 echo:; StallGuard threshold: echo: M914 X88 Y118 echo:; Driver stepping mode: echo: M569 S1 X Y Z echo: M569 S1 T0 E echo:; Linear Advance: echo: M900 K0.04 echo:; Filament load/unload: echo: M603 L0.00 U50.00 ; (mm) echo:; Filament runout sensor: echo: M412 S1 ; Sensor ON Exception in thread read thread: Traceback (most recent call last): File “printrun\printcore.py”, line 333, in \_readline File “printrun\printcore.py”, line 329, in \_readline\_nb File “serial\serialwin32.py”, line 295, in read