# Sovol Klipperized SV07 **URL:** https://forum.sovol3d.com/c/sv07/53.md [Latest](https://forum.sovol3d.com/latest.md) · [Categories](https://forum.sovol3d.com/categories.md) · [Tags](https://forum.sovol3d.com/tags.md) --- ## [About the Klipperized SV07 category](https://forum.sovol3d.com/t/about-the-klipperized-sv07-category/2621)
**Author:** [@sovol3d](https://forum.sovol3d.com/u/sovol3d)\ **Replies:** 5\ **Last updated:** [August 4, 2024, 3:53am UTC](https://forum.sovol3d.com/t/about-the-klipperized-sv07-category/2621 "2024-08-04T03:53:38Z")
Have any thoughts, questions, or insights about the newly released Sovol SV07? Here’s the place to spread your mind! Learn more about the Sovol SV07: Pre-order| Sovol SV07 Klipper Direct Drive Extruder 3D Printer Print… --- ## [Youtube for Sovol sv 07](https://forum.sovol3d.com/t/youtube-for-sovol-sv-07/10274)
**Author:** [@MayPrinting](https://forum.sovol3d.com/u/MayPrinting)\ **Replies:** 7\ **Last updated:** [August 14, 2026, 10:19am UTC](https://forum.sovol3d.com/t/youtube-for-sovol-sv-07/10274 "2026-08-14T10:19:42Z")
Hey everyone! I wanted to share a project I’ve been working on for the Sovol SV07: Sovol SV07 YouTube Extension. If you’ve ever wanted to watch videos or follow tutorials on your printer’s touchscreen while setting up … --- ## [Auto homing and mainsail error on Sovol sv 07](https://forum.sovol3d.com/t/auto-homing-and-mainsail-error-on-sovol-sv-07/9799)
**Author:** [@MayPrinting](https://forum.sovol3d.com/u/MayPrinting)\ **Replies:** 9\ **Last updated:** [March 27, 2026, 6:01am UTC](https://forum.sovol3d.com/t/auto-homing-and-mainsail-error-on-sovol-sv-07/9799 "2026-03-27T06:01:59Z")
Hello everyone, because of an firmware error I had to flash my Sovol sv 07. (Mainboard and Klipper screen.) Now after the flash, when I try to home the printer the Print Head doesn’t stop moving on the X-Axis. (Y-Axis w… --- ## [My Klipper screen will not boot up](https://forum.sovol3d.com/t/my-klipper-screen-will-not-boot-up/7143)
**Author:** [@thetractorist](https://forum.sovol3d.com/u/thetractorist)\ **Replies:** 7\ **Last updated:** [March 26, 2026, 12:12pm UTC](https://forum.sovol3d.com/t/my-klipper-screen-will-not-boot-up/7143 "2026-03-26T12:12:35Z")
My Klipper Screen starts to boot; I get the warp factor stars, then the printed robot, then the screen goes blank, and nothing. This is repeated every time I power up the unit. It has been working fine for weeks until … --- ## [Screen failure on SV07 plus](https://forum.sovol3d.com/t/screen-failure-on-sv07-plus/9690)
**Author:** [@loulnux](https://forum.sovol3d.com/u/loulnux)\ **Replies:** 4\ **Last updated:** [March 26, 2026, 6:07am UTC](https://forum.sovol3d.com/t/screen-failure-on-sv07-plus/9690 "2026-03-26T06:07:53Z")
Screen failure: the system seems to reboot at the startup animation; this cycle is endless. However, the printer remains fully functional via the intranet interface. I just can no longer control it manually. Any ideas? --- ## [Klipad50 won't boot](https://forum.sovol3d.com/t/klipad50-wont-boot/8136)
**Author:** [@cardoc](https://forum.sovol3d.com/u/cardoc)\ **Replies:** 3\ **Last updated:** [March 10, 2026, 11:02pm UTC](https://forum.sovol3d.com/t/klipad50-wont-boot/8136 "2026-03-10T23:02:10Z")
Just a PSA for those “fortunate” enough to be running the Sovol Kliad50 My unit sh!t the bed (again) so I assumed it was (as usual) an issue with the software on the EMMC so I grabbed my USB dongle and started the proce… --- ## [Errors after updating Klipper and moonraker](https://forum.sovol3d.com/t/errors-after-updating-klipper-and-moonraker/9686)
**Author:** [@iherreral](https://forum.sovol3d.com/u/iherreral)\ **Replies:** 4\ **Last updated:** [March 6, 2026, 9:52pm UTC](https://forum.sovol3d.com/t/errors-after-updating-klipper-and-moonraker/9686 "2026-03-06T21:52:30Z")
Hello, The situation is that after updating Klipper and Moonraker via the frontend, thinking nothing would break, it ended up breaking. Right now I have the versions And I have identified that there is a problem requ… --- ## [Sovol SV07 mcu firmware flashing](https://forum.sovol3d.com/t/sovol-sv07-mcu-firmware-flashing/9626)
**Author:** [@nussico](https://forum.sovol3d.com/u/nussico)\ **Replies:** 4\ **Last updated:** [February 16, 2026, 1:15am UTC](https://forum.sovol3d.com/t/sovol-sv07-mcu-firmware-flashing/9626 "2026-02-16T01:15:46Z")
Hey guys, I accidentally updated my Klipper setup, and when I tried updating my MCU so I could print again, it didn’t work with the SD card. Then I tried flashing it with an ST-Link V2, but now it doesn’t work at all. I … --- ## [Sovol SV07 MCU issue](https://forum.sovol3d.com/t/sovol-sv07-mcu-issue/8612)
**Author:** [@Brtcruiser](https://forum.sovol3d.com/u/Brtcruiser)\ **Replies:** 18\ **Last updated:** [February 13, 2026, 11:03am UTC](https://forum.sovol3d.com/t/sovol-sv07-mcu-issue/8612 "2026-02-13T11:03:20Z")
Hey all I can not figure out my sovol sv07. I did an update through Orca Slicer, and it broke my printer. I can’t get the moonraker to connect to klipper. I get an MCU failure, and klipper is constantly trying to start.… --- ## [Cant extrude on sovol sv07](https://forum.sovol3d.com/t/cant-extrude-on-sovol-sv07/9526)
**Author:** [@Bantingbintang](https://forum.sovol3d.com/u/Bantingbintang)\ **Replies:** 1\ **Last updated:** [February 7, 2026, 6:25am UTC](https://forum.sovol3d.com/t/cant-extrude-on-sovol-sv07/9526 "2026-02-07T06:25:45Z")
I’ve tried disassembling the filament feeder, but the filament is worn away by the feeder’s gears. I tried pushing the stuck filament at the point marked with the red arrow, but it’s very hard, even when using the includ… --- ## [New sv 07 rough noise and vibrations](https://forum.sovol3d.com/t/new-sv-07-rough-noise-and-vibrations/9363)
**Author:** [@Baasonen](https://forum.sovol3d.com/u/Baasonen)\ **Replies:** 4\ **Last updated:** [January 10, 2026, 7:55pm UTC](https://forum.sovol3d.com/t/new-sv-07-rough-noise-and-vibrations/9363 "2026-01-10T19:55:13Z")
I got my printer a few days ago and today it started to have a rough noise and vibrations. They get better on hugher layers and almost dissaper on layers \>20. By listening and feeling the machine I think they come from t… --- ## [SV07 stops mid print](https://forum.sovol3d.com/t/sv07-stops-mid-print/8644)
**Author:** [@Balek](https://forum.sovol3d.com/u/Balek)\ **Replies:** 2\ **Last updated:** [January 7, 2026, 6:59am UTC](https://forum.sovol3d.com/t/sv07-stops-mid-print/8644 "2026-01-07T06:59:19Z")
I received my printer a couple weeks ago. I am able to print smaller projects with minimal issues but when I print anything larger the printer will randomly stop and become completely unresponsive, beeping periodically. … --- ## [The Sv07 is still an amazing deal... but here is how you fix a brand new one](https://forum.sovol3d.com/t/the-sv07-is-still-an-amazing-deal-but-here-is-how-you-fix-a-brand-new-one/9349)
**Author:** [@SheepInACart](https://forum.sovol3d.com/u/SheepInACart)\ **Replies:** 3\ **Last updated:** [January 6, 2026, 4:26am UTC](https://forum.sovol3d.com/t/the-sv07-is-still-an-amazing-deal-but-here-is-how-you-fix-a-brand-new-one/9349 "2026-01-06T04:26:54Z")
Buckle up folks, this is gonna be a long one. First the software. No monitoring on CPU temperature of either STM32F103XE on main board (middle of bottom left of printer base where the big cables enter) or the MksPi Make… --- ## [SOVOL S7 and Sovol in General](https://forum.sovol3d.com/t/sovol-s7-and-sovol-in-general/3724)
**Author:** [@xxduffyxx](https://forum.sovol3d.com/u/xxduffyxx)\ **Replies:** 44\ **Last updated:** [December 23, 2025, 3:30pm UTC](https://forum.sovol3d.com/t/sovol-s7-and-sovol-in-general/3724 "2025-12-23T15:30:58Z")
Does Sovol want to be the worst 3D Printer company in existence? From there lack of QA to their lack of anything unless you have to join Facebook/Meta and have all your data stolen and sold. Support is a joke. If you … --- ## [Extruder temperature so far out of whack, unit won't start](https://forum.sovol3d.com/t/extruder-temperature-so-far-out-of-whack-unit-wont-start/9243)
**Author:** [@SammieC](https://forum.sovol3d.com/u/SammieC)\ **Replies:** 5\ **Last updated:** [December 19, 2025, 9:58pm UTC](https://forum.sovol3d.com/t/extruder-temperature-so-far-out-of-whack-unit-wont-start/9243 "2025-12-19T21:58:39Z")
On my unit recently, I started having issues with the temperature jumping around so bad that it shuts the unit down when it jumps out of the parameters. I tried reflashing the klipper with the standard firmware, but thi… --- ## [A problem as crept up again](https://forum.sovol3d.com/t/a-problem-as-crept-up-again/9173)
**Author:** [@PK63015](https://forum.sovol3d.com/u/PK63015)\ **Replies:** 4\ **Last updated:** [December 11, 2025, 2:13am UTC](https://forum.sovol3d.com/t/a-problem-as-crept-up-again/9173 "2025-12-11T02:13:04Z")
I had this problem before and I somehow fixed it, but only God knows what I did before. A little back story and what I have tried. I printed a rather large project and everything went fine. But after it finished I trie… --- ## [SV07 doesn't see my WIFI, but others](https://forum.sovol3d.com/t/sv07-doesnt-see-my-wifi-but-others/5916)
**Author:** [@JesterOne](https://forum.sovol3d.com/u/JesterOne)\ **Replies:** 8\ **Last updated:** [December 2, 2025, 3:11pm UTC](https://forum.sovol3d.com/t/sv07-doesnt-see-my-wifi-but-others/5916 "2025-12-02T15:11:21Z")
Hi, see topic, all of a sudden my printer won’t see my WIFI anymore. Nothing has changed since the last time I used the printer, no updates, didn’t even reboot the router or anything. When I go to the network page on t… --- ## [Sv07 doesn't power on. Klipper screen dead?](https://forum.sovol3d.com/t/sv07-doesnt-power-on-klipper-screen-dead/9026)
**Author:** [@conor](https://forum.sovol3d.com/u/conor)\ **Replies:** 2\ **Last updated:** [November 18, 2025, 5:25am UTC](https://forum.sovol3d.com/t/sv07-doesnt-power-on-klipper-screen-dead/9026 "2025-11-18T05:25:11Z")
Hello, I’ve owned my SV07 for roughly 2 years, and everything on the printer has functioned great. Recently, however, I tried to power on the printer, but it wouldn’t turn on. With the printer switched on, the Klipper s… --- ## [Bricked my printer - can't recover](https://forum.sovol3d.com/t/bricked-my-printer-cant-recover/9013)
**Author:** [@BlueRin](https://forum.sovol3d.com/u/BlueRin)\ **Replies:** 7\ **Last updated:** [November 17, 2025, 2:36pm UTC](https://forum.sovol3d.com/t/bricked-my-printer-cant-recover/9013 "2025-11-17T14:36:38Z")
Hey everyone! I kinda bricked my SV07, no luck with the usual recovery tutorials yet. but to start at the beginning: I wanted to add a webcam to the printer, for which I followed this official doc: It all went fine… --- ## [Gantry screw alignment issue](https://forum.sovol3d.com/t/gantry-screw-alignment-issue/9022)
**Author:** [@KenM](https://forum.sovol3d.com/u/KenM)\ **Replies:** 2\ **Last updated:** [November 17, 2025, 1:50pm UTC](https://forum.sovol3d.com/t/gantry-screw-alignment-issue/9022 "2025-11-17T13:50:12Z")
I have two SV07, and one SV07+. I just ordered two more SV07s (for a makerspace I run) and on one machine I could not attach the gantry to the base (the other was fine and it all worked). I can get 2 screws on either s… --- ## [Very bad Y-Shift](https://forum.sovol3d.com/t/very-bad-y-shift/8553)
**Author:** [@MichaelKng](https://forum.sovol3d.com/u/MichaelKng)\ **Replies:** 2\ **Last updated:** [November 17, 2025, 1:17am UTC](https://forum.sovol3d.com/t/very-bad-y-shift/8553 "2025-11-17T01:17:11Z")
Hello, i suddenly have very bad issues with Y-shift. On one point the layer shifts about 1-2mm, after that again perfectly straight. Happened with 3 Models so far, on one model even 2 times at the same height. I tried … --- ## [2 Problems with my printer](https://forum.sovol3d.com/t/2-problems-with-my-printer/8982)
**Author:** [@PK63015](https://forum.sovol3d.com/u/PK63015)\ **Replies:** 1\ **Last updated:** [November 11, 2025, 4:23pm UTC](https://forum.sovol3d.com/t/2-problems-with-my-printer/8982 "2025-11-11T16:23:48Z")
My Y Axis is out of alignment. It tries to print off the back of the print. The purge line prints to the Heated Bed connection. Another problem I have is when I try the Z Tilt it fails saying the increments are increasi… --- ## [SV07 Printer bed will not level](https://forum.sovol3d.com/t/sv07-printer-bed-will-not-level/8131)
**Author:** [@PengiunPreferred](https://forum.sovol3d.com/u/PengiunPreferred)\ **Replies:** 8\ **Last updated:** [November 9, 2025, 3:18am UTC](https://forum.sovol3d.com/t/sv07-printer-bed-will-not-level/8131 "2025-11-09T03:18:54Z")
Hi, I have had my SV07 working well for many months. Recently, the hot end began lightly scraping the print bed on one side (the right when looking from the front). This causes the first layer to fail. I have reset the… --- ## [Printing with TPU?](https://forum.sovol3d.com/t/printing-with-tpu/5715)
**Author:** [@tingo](https://forum.sovol3d.com/u/tingo)\ **Replies:** 9\ **Last updated:** [November 2, 2025, 12:33pm UTC](https://forum.sovol3d.com/t/printing-with-tpu/5715 "2025-11-02T12:33:09Z")
Is anyone printing TPU filament with their SV07 / SV07 Plus? Any success or failure reports? What filament / which Shore hardness did you use? See here for explanation of the hardness values. --- ## [Sovol 07 z Offset calibration problem](https://forum.sovol3d.com/t/sovol-07-z-offset-calibration-problem/7103)
**Author:** [@x-act](https://forum.sovol3d.com/u/x-act)\ **Replies:** 9\ **Last updated:** [September 16, 2025, 9:51am UTC](https://forum.sovol3d.com/t/sovol-07-z-offset-calibration-problem/7103 "2025-09-16T09:51:09Z")
Hello, I bought a Sovol07 and am trying to calibrate it according to the instructions! However, I’m already failing at the Z-offset. I can’t lower the extruder far enough for the nozzle to even come close to touching the… --- ## [When itry to boot up my SV07 it boots up most of the way and then starts at the begining again and gets cought in a loop](https://forum.sovol3d.com/t/when-itry-to-boot-up-my-sv07-it-boots-up-most-of-the-way-and-then-starts-at-the-begining-again-and-gets-cought-in-a-loop/8470)
**Author:** [@Fezbunny](https://forum.sovol3d.com/u/Fezbunny)\ **Replies:** 23\ **Last updated:** [August 16, 2025, 4:11am UTC](https://forum.sovol3d.com/t/when-itry-to-boot-up-my-sv07-it-boots-up-most-of-the-way-and-then-starts-at-the-begining-again-and-gets-cought-in-a-loop/8470 "2025-08-16T04:11:31Z")
when itry to boot up my SV07 it boots up most of the way and then starts at the begining again and gets cought in a loop --- ## [Fillament load dosent work](https://forum.sovol3d.com/t/fillament-load-dosent-work/8045)
**Author:** [@CaydeNine](https://forum.sovol3d.com/u/CaydeNine)\ **Replies:** 1\ **Last updated:** [June 11, 2025, 10:01pm UTC](https://forum.sovol3d.com/t/fillament-load-dosent-work/8045 "2025-06-11T22:01:29Z")
Reloading filament doesn’t work. When I insert the filament and tell the printer to load it, it pulls it in a bit and then stops. Even if I let the printer run for a while, nothing happens. I cleaned the print head, b… --- ## [Really bad X axis layer shift](https://forum.sovol3d.com/t/really-bad-x-axis-layer-shift/7856)
**Author:** [@Fezbunny](https://forum.sovol3d.com/u/Fezbunny)\ **Replies:** 22\ **Last updated:** [June 8, 2025, 2:44am UTC](https://forum.sovol3d.com/t/really-bad-x-axis-layer-shift/7856 "2025-06-08T02:44:27Z")
So I recently got the SV07 as my first real printer and it’s been great until today when I’ve been getting really bad layer shifts on the X axis I just tried to print a webcam mount and it shifts almost completely off of… --- ## [SV07 Plus boot issues](https://forum.sovol3d.com/t/sv07-plus-boot-issues/7996)
**Author:** [@chris11](https://forum.sovol3d.com/u/chris11)\ **Replies:** 1\ **Last updated:** [June 6, 2025, 3:13pm UTC](https://forum.sovol3d.com/t/sv07-plus-boot-issues/7996 "2025-06-06T15:13:28Z")
Hi Community, i have issues with my SV07 Plus after a failed update. I bough an MKS emmc adapter and flashed the emmc again via Sovol instructions and also with this image(GitHub - TomasOlsson/BrickedSv07-Sv07Plus: This… --- ## [Add USB camera, is it possible?](https://forum.sovol3d.com/t/add-usb-camera-is-it-possible/3077)
**Author:** [@sovol3delger](https://forum.sovol3d.com/u/sovol3delger)\ **Replies:** 11\ **Last updated:** [May 30, 2025, 3:08am UTC](https://forum.sovol3d.com/t/add-usb-camera-is-it-possible/3077 "2025-05-30T03:08:52Z")
This might sound like a really stupid question (because it probably is)… Does anyone know if you can plug a USB webcam into the control pad and show the stream through the web interface? I can see that there is a secti… [Next page](https://forum.sovol3d.com/c/sv07/53.md?page=1)